BIT HOLDERS & EXTENSIONS
Features of this product include:
- Driver sizes: ¼”, ⅜”, ½”
- Rust-resistant
- Ball-bearing lock
- Sturdy spring-loaded ball bearing holds sockets securely.
- Turns any power drill into a power nut driver
- Must-have accessory set for power drills and impact drivers
- Extensions in lengths 6", 4" & 2" for superior access for hard-to-reach fasteners
- Strong permanent magnets hold bits securely in place
- accepts all 1/4" hex-shank bits 1/4" quick-change hex shanks fit all power drills, 1/4" impact drivers and hand-held drivers
- Hardened tempered tool steel with chrome-finish holders
MERCER/CHAMPION 1 1/2" DIA. x 1/4" SHANK CRIMPED WIRE WHEEL$5.59182010B182010B MERCER 1 1/2" DIA. x 1/4" SHANK CRIMPED WIRE WHEEL 20,000 RPM ,.008 Stainless steel Product Features Crimped wire wheels for drills and die grinders 1-1/2-Inch by 1/4-Inch shank Wire Type: 0.008 Stainless Steel 20-Pack Wire brushes available in all different styles and sizes
4301 5C Spin-Index Fixture (without collets)$79.0043014301 5C Spin-Index Fixture (without collets) . The 5C Spin Indexer is a quick, simple and accurate device for mill work. Mount your workpiece in the 5C Collet and thread it into the indexer. Great for miniature work such as clock gears. Comes complete with precision ground, 36-position index plate, calibrated in 1 degree increments. 5C collet not included.
1/4" x 2 1/2" Square Handle Wire lock Pin (sold in pack of 10)$14.491/4" x 2 1/2" Square Handle PTO Hitch Pins (sold in pack of 10)21972
MILTON Volume Safety Blo-Gun Made in U.S.A.$13.49S132 MILTON Volume Safety Blo-Gun. Special venture holes in the extension tube increase the air volume approximately 5 times that of conventional blo-guns and yet maintain required noise level and required nozzle pressure with inlet pressure of 150 PSI allows air to escape if end of extension is blocked. Made in U.S.A.S132
MILTON Safety Blow Gun Made in U.S.A.$9.95Milton Industries S-150 Full-Flow Safety Lever Blo-Gun Made in U.S.A. Maximum working pressure: 150 PSI SCFM 10 @ 100 PSI 1/4 NPT air inlet Nozzle thread size: 7/16 -27 OSHA compliantS150
MERCER/CHAMPION Abrasives 4 pc File Set$8.99BFS604BFS604 Mercer Abrasives 4 pc File Set . The perfect set for the ‘Do-It-Yourself’ market. Packaged in a plastic pouch. Contents: (1) 8″ 4-in-1 Shoe Rasp #BSR08 (1) 6″ Slim Taper #BTRS06 (1) 6″ Round #BROB06 (1) 8″ Mill Bastard #BFMB08
MILTON "M" Style 1/4" NPT Male Coupler Plug (Most Popular) Made in U.S.A.$1.85727 MILTON "M" Style 1/4" NPT Male Coupler Plug (Most Popular) Made in U.S.A.727
DeWALT 4 1/2"-5" High Performance Angle Grinder$172.00D28131 DeWALT 4 1/2"-5" High Performance Angle Grinder FEATURES 13.0 amp/2.3HP, 11,000 rpm DEWALT built G55 (AC) motor designed for faster material removal and higher overload protectionDust Ejection System™ provides durability by ejecting damaging dust and debris particles that enter the tool through the air intake ventsQuick-Change™ Wheel Release allows tool-free wheel removalDual Abrasion Protection provides increased motor protection from damaging dust and debris ingestionOne-piece brush arm prevents brush hang-up due to dust ingestionE-Clutch® shuts the grinder off when a wheel pinch or wheel stall occurs, extending the life of the gears and motorPower-Off® Advanced Overload Protection shuts the tool off before it reaches overload or burn-upPower-Loss Reset® prevents accidental restarts following a power disruption when the tool is left in the "on" positionVibration-reducing side handle increases comfort for extended use applicationsLow profile, jam-pot gear case provides precise gear alignment for a smoother, quieter transmission while allowing access to tight spacesAuto-off brushes shut the tool down when the brushes need replacing to avoid tool damageKeyless adjustable guard provides tool-free guard adjustments to increase productivityLock-on slide switch provides increased user comfort in extended use applicationsD28131
